This *** book starts with the first ****** post.

After converting the partition format, upgrading the computer, using the virtual optical drive, and installing many hard drives..., there may be chaos in the disk letters. How should you "get it right" in the face of this phenomenon? I believe the few methods provided below in this article will help you.

Blocking hard disk method

Set the master-slave relationship between the two hard disks and connect them correctly, then turn on the computer and enter the bios setting program. Set the slave disk parameter item to "none" in the "standardcmosfeatures" option to block the slave disk. Set the master disk as the boot hard disk in the "advancedbiosfeatures" option. After saving the settings, restart the hard disk drive letters will be arranged in the order of partitions of the master and slave disks. The disadvantage of this method is that the slave disk can only be used normally in indos, and the slave disk cannot be recognized in pure dos mode.

Repartition

After setting up the master-slave relationship and correctly connecting the hard disk, use any partitioning software to divide all slave disks into logical partitions, and the drive letters of slave disk [1] will be arranged behind the master disk in order. (Chen Huian)

in9x

Using letterassigner

The letterassigner can arbitrarily specify the drive letter of the hard disk. Start the letterassigner, and 26 drive letters "a~z" are listed below the toolbar of the letterassigner. Yellow means you can choose to use it now, and gray means you cannot use it now. Select the drive letter that needs to be modified in the main window, and then select the modified drive letter from the drive letter bar, execute the "File → Save" command, and restart the computer.

During the operation, if you need to give up the modification, just execute "Edit → Restore Original" or press the "ctrlz" key combination. Generally, the drive letter of the system disk cannot be modified, otherwise it may cause a system startup error. When modifying the drive letter of the system disk, a prompt window will pop up by the letterassigner. (lanfu)

System Setting Method

indos2000/xp/2003

Modifying the malfunctioning drive letters in indos2000/xp/2003 is very simple. It can be easily done through the system's own "disk management" program. Click "Start → Run" to start "Disk Management". Let's take a look at how to modify the drive letters.

Step 1: As shown in Figure 1, right-click the drive that needs to modify the drive letter and select the "Change drive letter and path" command. When changing the drive letter of the drive, be careful that the drive letter of the system disk cannot be modified and is not allowed to be modified at will, otherwise the system will not be started.

Step 2: Press the "Change Drive Letter and Path" dialog box that pops up, and in the next window, specify a new drive letter (drive letter) for the drive.

Tip: If the drive letter you want to specify has been occupied by another disk partition, you can first modify the disk partition that occupies the drive letter, specify it as another disk letter, and release the drive letter occupied by the disk partition.

indos9e

In indos9e, you can usually only set the master-slave jumper and bios settings of the hard disk, or use the third-party tool Letter Assigner to adjust the hard disk drive letter. We just click the disk partition to change in the program (as shown in Figure 2), then specify the English drive letter on the toolbar, and after adjustment, press "File → Save" to save the settings, and restart the computer. It should be noted that letter Assigner cannot modify the partition where the indos system is located. When you make inappropriate adjustments, letter Assigner will appear to remind you that you must not forcefully modify it. Finally, if you are using a memory emulated hard disk (virtual hard disk), letter Assigner can also specify the virtual disk letter by identifying the "ms-ramdrive" disk volume label.

Use partitionmagic

partitionmagic can repartition, format, copy partitioning and other operations on the hard disk. The operation method of using it to modify the drive letter is as follows:

Start partitionmagic, right-click the drive letter that needs to be modified, select "Advanced → Modify drive letter" in the shortcut menu, and then select the new drive letter in the pop-up "Change drive letter" window, click the "OK" button, then select the "General → Apply Change" command, and restart as prompts.

Other:

(1) indos2000/xp

This *** book starts with the first ****** post.

After converting the partition format, upgrading the computer, using the virtual optical drive, and installing many hard drives..., there may be chaos in the disk letters. How should you "get it right" in the face of this phenomenon? I believe the few methods provided below in this article will help you.

This *** book starts with the first ****** post.

After converting the partition format, upgrading the computer, using the virtual optical drive, and installing many hard drives..., there may be chaos in the disk letters. How should you "get it right" in the face of this phenomenon? I believe the few methods provided below in this article will help you.

Blocking hard disk method

Set the master-slave relationship between the two hard disks and connect them correctly, then turn on the computer and enter the bios setting program. Set the slave disk parameter item to "none" in the "standardcmosfeatures" option to block the slave disk. Set the master disk as the boot hard disk in the "advancedbiosfeatures" option. After saving the settings, restart the hard disk drive letters will be arranged in the order of partitions of the master and slave disks. The disadvantage of this method is that the slave disk can only be used normally in indos, and the slave disk cannot be recognized in pure dos mode.

Repartition

After setting up the master-slave relationship and correctly connecting the hard disk, use any partitioning software to divide all slave disks into logical partitions, and the drive letters of slave disk [1] will be arranged behind the master disk in order. (Chen Huian)

in9x

Using letterassigner

The letterassigner can arbitrarily specify the drive letter of the hard disk. Start the letterassigner, and 26 drive letters "a~z" are listed below the toolbar of the letterassigner. Yellow means you can choose to use it now, and gray means you cannot use it now. Select the drive letter that needs to be modified in the main window, and then select the modified drive letter from the drive letter bar, execute the "File → Save" command, and restart the computer.

During the operation, if you need to give up the modification, just execute "Edit → Restore Original" or press the "ctrlz" key combination. Generally, the drive letter of the system disk cannot be modified, otherwise it may cause a system startup error. When modifying the drive letter of the system disk, a prompt window will pop up by the letterassigner. (lanfu)

System Setting Method

indos2000/xp/2003

Modifying the malfunctioning drive letters in indos2000/xp/2003 is very simple. It can be easily done through the system's own "disk management" program. Click "Start → Run" to start "Disk Management". Let's take a look at how to modify the drive letters.

Step 1: As shown in Figure 1, right-click the drive that needs to modify the drive letter and select the "Change drive letter and path" command. When changing the drive letter of the drive, be careful that the drive letter of the system disk cannot be modified and is not allowed to be modified at will, otherwise the system will not be started.

Step 2: Press the "Change Drive Letter and Path" dialog box that pops up, and in the next window, specify a new drive letter (drive letter) for the drive.

Tip: If the drive letter you want to specify has been occupied by another disk partition, you can first modify the disk partition that occupies the drive letter, specify it as another disk letter, and release the drive letter occupied by the disk partition.

indos9e

In indos9e, you can usually only set the master-slave jumper and bios settings of the hard disk, or use the third-party tool Letter Assigner to adjust the hard disk drive letter. We just click the disk partition to change in the program (as shown in Figure 2), then specify the English drive letter on the toolbar, and after adjustment, press "File → Save" to save the settings, and restart the computer. It should be noted that letter Assigner cannot modify the partition where the indos system is located. When you make inappropriate adjustments, letter Assigner will appear to remind you that you must not forcefully modify it. Finally, if you are using a memory emulated hard disk (virtual hard disk), letter Assigner can also specify the virtual disk letter by identifying the "ms-ramdrive" disk volume label.

Use partitionmagic

partitionmagic can repartition, format, copy partitioning and other operations on the hard disk. The operation method of using it to modify the drive letter is as follows:

Start partitionmagic, right-click the drive letter that needs to be modified, select "Advanced → Modify drive letter" in the shortcut menu, and then select the new drive letter in the pop-up "Change drive letter" window, click the "OK" button, then select the "General → Apply Change" command, and restart as prompts.

Other:

(1) indos2000/xp

This *** book starts with the first ****** post.

After converting the partition format, upgrading the computer, using the virtual optical drive, and installing many hard drives..., there may be chaos in the disk letters. How should you "get it right" in the face of this phenomenon? I believe the few methods provided below in this article will help you.

Blocking hard disk method

Set the master-slave relationship between the two hard disks and connect them correctly, then turn on the computer and enter the bios setting program. Set the slave disk parameter item to "none" in the "standardcmosfeatures" option to block the slave disk. Set the master disk as the boot hard disk in the "advancedbiosfeatures" option. After saving the settings, restart the hard disk drive letters will be arranged in the order of partitions of the master and slave disks. The disadvantage of this method is that the slave disk can only be used normally in indos, and the slave disk cannot be recognized in pure dos mode.

Repartition

After setting up the master-slave relationship and correctly connecting the hard disk, use any partitioning software to divide all slave disks into logical partitions, and the drive letters of slave disk [1] will be arranged behind the master disk in order. (Chen Huian)

This *** book starts with the first ****** post.

After converting the partition format, upgrading the computer, using the virtual optical drive, and installing many hard drives..., there may be chaos in the disk letters. How should you "get it right" in the face of this phenomenon? I believe the few methods provided below in this article will help you.

Blocking hard disk method

Set the master-slave relationship between the two hard disks and connect them correctly, then turn on the computer and enter the bios setting program. Set the slave disk parameter item to "none" in the "standardcmosfeatures" option to block the slave disk. Set the master disk as the boot hard disk in the "advancedbiosfeatures" option. After saving the settings, restart the hard disk drive letters will be arranged in the order of partitions of the master and slave disks. The disadvantage of this method is that the slave disk can only be used normally in indos, and the slave disk cannot be recognized in pure dos mode.

Repartition

After setting up the master-slave relationship and correctly connecting the hard disk, use any partitioning software to divide all slave disks into logical partitions, and the drive letters of slave disk [1] will be arranged behind the master disk in order. (Chen Huian)

in9x

Using letterassigner

The letterassigner can arbitrarily specify the drive letter of the hard disk. Start the letterassigner, and 26 drive letters "a~z" are listed below the toolbar of the letterassigner. Yellow means you can choose to use it now, and gray means you cannot use it now. Select the drive letter that needs to be modified in the main window, and then select the modified drive letter from the drive letter bar, execute the "File → Save" command, and restart the computer.

During the operation, if you need to give up the modification, just execute "Edit → Restore Original" or press the "ctrlz" key combination. Generally, the drive letter of the system disk cannot be modified, otherwise it may cause a system startup error. When modifying the drive letter of the system disk, a prompt window will pop up by the letterassigner. (lanfu)

System Setting Method

indos2000/xp/2003

Modifying the malfunctioning drive letters in indos2000/xp/2003 is very simple. It can be easily done through the system's own "disk management" program. Click "Start → Run" to start "Disk Management". Let's take a look at how to modify the drive letters.

Step 1: As shown in Figure 1, right-click the drive that needs to modify the drive letter and select the "Change drive letter and path" command. When changing the drive letter of the drive, be careful that the drive letter of the system disk cannot be modified and is not allowed to be modified at will, otherwise the system will not be started.

Step 2: Press the "Change Drive Letter and Path" dialog box that pops up, and in the next window, specify a new drive letter (drive letter) for the drive.

Tip: If the drive letter you want to specify has been occupied by another disk partition, you can first modify the disk partition that occupies the drive letter, specify it as another disk letter, and release the drive letter occupied by the disk partition.

indos9e

In indos9e, you can usually only set the master-slave jumper and bios settings of the hard disk, or use the third-party tool Letter Assigner to adjust the hard disk drive letter. We just click the disk partition to change in the program (as shown in Figure 2), then specify the English drive letter on the toolbar, and after adjustment, press "File → Save" to save the settings, and restart the computer. It should be noted that letter Assigner cannot modify the partition where the indos system is located. When you make inappropriate adjustments, letter Assigner will appear to remind you that you must not forcefully modify it. Finally, if you are using a memory emulated hard disk (virtual hard disk), letter Assigner can also specify the virtual disk letter by identifying the "ms-ramdrive" disk volume label.

Use partitionmagic

Repartition, format, copy partitioning and other operations. The operation method of using it to modify the drive letter is as follows:

This *** book starts with the first ****** post.

After converting the partition format, upgrading the computer, using the virtual optical drive, and installing many hard drives..., there may be chaos in the disk letters. How should you "get it right" in the face of this phenomenon? I believe the few methods provided below in this article will help you.

Blocking hard disk method

Set the master-slave relationship between the two hard disks and connect them correctly, then turn on the computer and enter the bios setting program. Set the slave disk parameter item to "none" in the "standardcmosfeatures" option to block the slave disk. Set the master disk as the boot hard disk in the "advancedbiosfeatures" option. After saving the settings, restart the hard disk drive letters will be arranged in the order of partitions of the master and slave disks. The disadvantage of this method is that the slave disk can only be used normally in indos, and the slave disk cannot be recognized in pure dos mode.

Repartition

After setting up the master-slave relationship and correctly connecting the hard disk, use any partitioning software to divide all slave disks into logical partitions, and the drive letters of slave disk [1] will be arranged behind the master disk in order. (Chen Huian)

Blocking hard disk method

Set the master-slave relationship between the two hard disks and connect them correctly, then turn on the computer and enter the bios setting program. Set the slave disk parameter item to "none" in the "standardcmosfeatures" option to block the slave disk. Set the master disk as the boot hard disk in the "advancedbiosfeatures" option. After saving the settings, restart the hard disk drive letters will be arranged in the order of partitions of the master and slave disks. The disadvantage of this method is that the slave disk can only be used normally in indos, and the slave disk cannot be recognized in pure dos mode.

Repartition
Chapter completed!